DisplayNet Logo

DisplayNet DN-100 Series

DisplayNet DN-100 Series

Models

  • DN-100TX: Transmitter
  • DN-100RX: Receiver

Pricing: Call for a quote or demo

Availability: Shipping Now




DisplayNet
DN-100 Series Overview

The DN-100 Series is the first in an expanding range of DisplayNet AV-over-IP products. Each DN-100TX transmitter unit accepts multiple source signals including HDMI (with embedded audio and HDCP), analog stereo audio, bidirectional IR, RS-232, and 1GbE Ethernet. Using SDVoE technology, these input signals are packetized into a single 10GbE link, without the use of CODECs, and are distributed to destinations via an off-the-shelf 10GbE network switch using a single CAT6a or CAT7 cable up to 328 ft. (100 meters). The 10GbE switch provides a highly efficient and reliable means of distributing AV signals from many sources to an array of DN-100RX receiver units, which convert the packetized 10GbE data to AV output signals at the destination in real time without frame latency or any loss of image quality.

The DN-100 Series distributes uncompressed video with resolutions up to 4K /30p (4:4:4) and 4K /60p (4:2:0) without image artifacts and without frame latency. Video signals may be routed in Point-to-Point, Matrix Switching and Video Wall modes all in the same system. For optimum flexibility, each signal layer (Video, Audio, IR, RS‑232, etc.) can be routed completely independently from one another. Advanced audio features are supported, including: networked audio, audio embedding, de-embedding and down‑mixing. DN‑100 Series transmitter and receiver units are controlled by a DisplayNet Server™, which includes powerful DisplayNet Manager™ software that enables the system to be managed using any third party controller using simple Telnet commands.

Features
  • Utilizes SDVoE Technology to distribute AV signals with off-the-shelf 10GbE network switches
  • Fast / Seamless Switching of HDMI signals up to 4K /30p (4:4:4), and 4K /60p (4:2:0)
  • Vastly superior to existing Video-over-IP products: zero frame latency, zero compression, zero artifacts
  • Supports HDMI, HDCP, Embedded Audio, Analog Stereo Audio, Downmixed Audio, RS-232, Bidirectional IR, and 1GbE over 10GbE link
  • Fully Routable, Independent Switching Layers for all signal types: Video, Analog Audio, Downmixed Audio, IR, RS-232
  • Supports Audio Embedding, De-embedding and Down-Mixing
  • Create, save, and use video wall configurations with optimized bezel correction
  • Unconstrained scalability - Size of I/O array only limited by number of 10GbE switch ports
  • Maximum range up to 100 meters (328 ft.) using a single CAT6a or CAT7 cable
  • DisplayNet Server™ and DisplayNet Manager™ enable deep integration into new or existing AV systems
  • All endpoints include a built-in 1GbE Ethernet switch for high-speed local network connections
Benefits
  • Leverages decades of proven networking technology and massive global deployment of 10GbE networks
  • AV assets no longer need to be aggregated at a central location using an expensive AV Matrix Switcher
  • Eliminates the need for costly, redundant AV networks as all AV assets can now reside on existing IT networks
  • Enables IT Managers to easily manage and distribute AV assets within corporate network environments
  • 10GbE network switches can be up to 60% smaller than typical AV switches and up to 1/10th the cost
  • Scalable - system array limited only by the number of installed endpoints and size (ports) of 10GbE switch
  • High-speed uplinks on many 10GbE switches allow increased port capacity without obsoleting existing hardware
  • Capable of concurrent Video Wall and Matrix Switching operation - supports diverse range of applications
  • Embedded Local Management - DisplayNet™ auto-configures all connected devices even in the most complex networked systems, thus eliminating the need for complicated network switch configuration
Supported AV Signals
Video HDMI v1.4, DVI 1.0 and HDCP 1.4
HDCP Supports HDMI signals with or without HDCP encryption
Embedded Audio Supports routing of up to 8 channels of HDMI embedded LPCM digital audio with up to 24-bit depth and 192 kHz sampling frequency.

Supports pass-through of embedded HBR audio formats such as: Dolby Digital TrueHD, and DTS-HD Master Audio.
Downmixed Audio Embedded HDMI audio may be downmixed, re-sampled and switched as a separate layer
External Audio Unbalanced analog stereo audio inputs and outputs with up to 24-bit depth and a fixed 48 kHz sampling rate
Audio-over-IP Supports networked audio pass-through using 1GbE port
Ethernet Built-in 1GbE Ethernet switch on all Tx and Rx units supporting 10 Mbps. up to 1 Gbps.
IR Control Supports bidirectional IR pass-through
RS-232 Control Supports bidirectional RS-232 pass-through UART interface with up to 115,200 baud
Connections / Indicators
10GbE Port (1) 1ea. shielded RJ45 connector with LED indicators
HDMI Input / HDMI Output 1ea. 19-pin Female HDMI connector
Analog Stereo Audio 1ea. 3.5mm Stereo-Mini Jack (Input / Output on TX and Output on RX)
1GbE Port (1) 1ea. shielded RJ45 connector with LED indicators
RS-232 1ea. 3-pin, 3.5mm pitch, Phoenix connector, mates with Phoenix p.n. 1844223
IR Control 1ea. IR IN: 3.5mm Stereo Mini-Jack
1ea. IR OUT: 3.5mm Mini-Jack
DC Power 1ea. 5.5 mm / 2.0 mm female locking connector
Diagnostic LEDs Power, HDMI Link, TX/RX Link, and Status LEDs
Hardware Reset 1ea. Push-button to restore factory default values
Performance
Supported Resolutions Up to 4096x2160 or 3840x2160 /30p (4:4:4) 8-bit, and 3840x2160 /60p (4:2:0) 8-bit
Maximum Pixel Clock Freq. Supports pixel clock rates up to 300 MHz
Maximum Video Bit Rate Supports digital signal bit rates up to 3.0 Gbps./color, 9.0 Gbps. total
Switching Layers Independent switching layers for all connected Video, Analog Audio, Downmixed Audio, RS-232 and IR
Video Signal Latency Genlocked Mode: ≤ 30 µsec. (zero frame latency)

Fast Switched Mode: not more than 2x video frames:
@ 60Hz not more than 33.3 msec.
@ 30Hz not more than 67.7 msec.
10GbE Switch Requirements Required Features: 10GbE, non-blocking, Layer 2, Multicast with IGMP Snooping, Fast Leave
Supported I/O Switching Array Size of I/O array is only limited by the size (number of ports) of the 10GbE network switch
Recommended CAT Cable CAT-6A S/FTP (500 MHz) AWG 23, or CAT-7 (Europe); Compliant with TIA/EIA-568B termination standard
Maximum Cable Distance up to 328 ft. (100 meters) using CAT-6A S/FTP (500 MHz) AWG 23 cable
HDMI Input Cable Equalization Supports DVIGear's SHR™ Series HDMI with cable lengths up to 15 meters at 4K /30p resolution
Operational Modes (2)
Matrix Switching Mode Fully non-blocking cross-point routing of nearly any size I/O array - only limited by size of 10GbE switch.
Video Wall Mode Supports Video Wall displays using basic pixel allocation method. Consult DVIGear for further details.
Point-to-Point Mode Supports Point-to-Point Extension of signals up to 328 ft. (100 meters) using recommended cable.
Power
Typical Power Consumption Tx unit: 12.6 watts; Rx unit: 12.7 watts
External AC Power Adapter Input: 100-240VAC, 50-60Hz / Output: +12VDC @ 2.5A
Mechanical
Construction Heavy-duty steel enclosure with jet black finish
Dimensions (H x W x D) Each Unit: 1.4" x 8.3" x 5.1" (35.1 mm x 210.2 mm x 130.3 mm)
Weight Each Unit: 2.9 lbs. (1.3 kg)
Environmental
Operating Temp. (Environment) +32° to +104° F (0° to +40° C)
Typical Case Temperature Tx Unit: 98.6° F (37° C) Rx Unit: 105.8° F (41° C)
Storage Temp. (Environment) -4° to +158° F (-20° to +70° C)
Operating / Storage Humidity 10% to 90% (non-condensing)
Regulatory Approvals
TX / RX Units FCC, CE, RoHS
External AC Power Adapter FCC, CE, UL, C-UL, CEC, GS, PSE, CCC, RoHS, WEEE
Warranty
Limited Warranty 3 Years Parts and Labor
Model Numbers
DN-100TX DisplayNet HDMI 10GbE Transmitter
DN-100RX DisplayNet HDMI 10GbE Receiver
DNS-100 DisplayNet Server™: Rack-mountable Windows 10 PC with DisplayNet API and DisplayNet Manager™ Software pre-installed.
Accessories
Included 1x External AC Power Adapter (per unit)
2x Mounting Brackets with Screws (per unit)
1x HDMI Gold-Plated Jack Screw (per unit)
1x 3-pin RS-232 Phoenix Connector (Phoenix p.n. 1844223) (per unit)
1x IR Transmitter (per DN-100TX)
1x IR Receiver (per DN-100RX)
1x USB Flash Drive Loaded with: DisplayNet Hardware Manual and Software Manual
Optional DisplayNet Server™ (model DNS-100) (3)
External AC Power Adapter with USA, Euro, UK, or Australia Plugs (p.n. DVI-72155-PS)
Power Distribution Unit, 8x 12VDC (DVI-7520-PDU)
IR Transmitter (DVI-7360-IR-TX)
IR Receiver (DVI-7360-IR-RX)
19" Rack Mount Kit (DN-100-RMK)
DVI-I Female to HDMI Male Adapter Cable (DVI-8511b)

Note 1: The 10GbE port is designed to connect to compatible DVIGear products and 10GbE network switches only. Do not connect any device to the 10GbE port of this product unless you are sure it is compatible.

Note 2: A system may operate concurrently in Matrix Switching and Video Wall modes.

Note 3: The DisplayNet Server™ is recommended for optimal system configuration. Please see the DisplayNet DN-100 Series Hardware Manual for details on the DisplayNet Server™ specifications, installation, and use.

Note 4: All specifications are subject to change without notice.

Data Sheet

DN-100 Series Data Sheet

Download >